BMW 5 series E39

Since 1996-2001 of release

Repair and car operation



BMW E39
+ Introduction
+ The maintenance instruction
+ Current leaving and service
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of a body
   Care of the panels of furnish made of vinyl
   Care of an upholstery and salon rugs
   Repair of insignificant damages кузовных panels
   Repair of considerable damages of a body
   Kuzovnye backlashes
   Removal and installation of a forward bumper
   Removal and installation of shock-absorbers of a forward bumper
   Removal and installation of a back bumper
   Removal and installation of the shock-absorber of a back bumper
   Removal and installation of a forward wing
   Removal and cowl installation
   Adjustment of position of a cowl
   Removal and installation of a cover of a luggage carrier
   Adjustment of position of a cover of a luggage carrier
   Removal and installation of back facing of a luggage carrier
   Removal and installation of the lock of a cover of a luggage carrier/cylinder of the lock
   Removal and installation газонаполненного an emphasis of a cowl/cover of a luggage carrier
   Overlay replacement / a firm inscription
   Removal, installation and door adjustment
   Removal and installation of facing of a door
   Removal and door-lock installation
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock
   Removal and installation of the electric motor/microswitch of the uniform lock
   Removal, installation and adjustment of door glass
   Removal and installation electric стеклоподъемника
   Removal and installation of an external mirror
   Removal and installation of glass of a mirror
   Removal and installation of the case of an external mirror
   Removal and installation of an internal mirror
   Removal and installation of the central console
   Removal and electric motor installation сдвижной panels of the hatch of a roof
   Removal and installation of a forward seat
   The device of a tension of a seat belt
   Security measures at the reference with the device of a tension of a belt
   Protection of the device of a tension of a belt
   Removal and installation of a back seat
   Removal and shelf installation under a headdress
   Removal and installation of jalousie of back glass
+ Onboard electric equipment
+ Electric equipment schemes
+ System of onboard diagnostics


Removal and door-lock installation

 REMOVAL

1. Close a window of a forward door. Other windows open.
2. Disconnect a cable of weight from the storage battery. The battery is in a luggage carrier behind the right lateral facing.

At a battery detachment the data in electronic blocks of memory, for example, memories of malfunctions of the engine is erased. Address to recommendations Has undressed Removal and installation of the storage battery.

3. Isolate a negative pole of the storage battery to exclude casual contact.
4. Remove door facing.

Observe security measures concerning a safety pillow, address to Security measure Section at work with a safety pillow.

5. Расстыкуйте штекерное connection (orange) a lateral pillow of safety. Disconnect a pillow, having turned away screws of fastening and put its cover upward, for example in a luggage carrier.
6. Remove the door handle.

7. Cautiously remove plastic facing in a back part of cut of a door, incline it forward and fix in such position by a sticky tape (1).

8. Disconnect at a door-lock a nipple (1) and a cable (2).

9. Расстыкуйте штекерное connection of the microswitch of the uniform lock also take out it downwards.


 INSTALLATION

1. Check up, whether there is a clip pad (for the blade) below in the middle.

2. Insert the lock into a door. Thus a clip (1) (for the blade) the lock enter upwards into the blade (2) cylinders of the lock.

3. Join штекерное connection of the electric motor of the uniform lock and fix it.
4. Connect the microswitch tip.
5. Insert a nipple and a drive cable into the lock.
6. Insert a handle cable into a door skeleton.
7. Accurately paste пенопластовую facing on door cut.

Avoid facing damages as it can lead to draught occurrence in salon. The glutinous weight should be put on all contour of facing.

8. Establish the external handle of a door.
9. Fix on a door skeleton a lateral pillow of safety. Join штекерное connection (orange) a lateral pillow of safety.
10. Establish internal facing of a door.
11. Attach a weight cable to the storage battery. Establish hours. Program radio receiver stations.
12. Check up work of a door-lock, a drive of the lock and the uniform lock.