BMW 5 series E39

Since 1996-2001 of release

Repair and car operation



BMW E39
+ Introduction
+ The maintenance instruction
+ Current leaving and service
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of a body
   Care of the panels of furnish made of vinyl
   Care of an upholstery and salon rugs
   Repair of insignificant damages кузовных panels
   Repair of considerable damages of a body
   Kuzovnye backlashes
   Removal and installation of a forward bumper
   Removal and installation of shock-absorbers of a forward bumper
   Removal and installation of a back bumper
   Removal and installation of the shock-absorber of a back bumper
   Removal and installation of a forward wing
   Removal and cowl installation
   Adjustment of position of a cowl
   Removal and installation of a cover of a luggage carrier
   Adjustment of position of a cover of a luggage carrier
   Removal and installation of back facing of a luggage carrier
   Removal and installation of the lock of a cover of a luggage carrier/cylinder of the lock
   Removal and installation газонаполненного an emphasis of a cowl/cover of a luggage carrier
   Overlay replacement / a firm inscription
   Removal, installation and door adjustment
   Removal and installation of facing of a door
   Removal and door-lock installation
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock
   Removal and installation of the electric motor/microswitch of the uniform lock
   Removal, installation and adjustment of door glass
   Removal and installation electric стеклоподъемника
   Removal and installation of an external mirror
   Removal and installation of glass of a mirror
   Removal and installation of the case of an external mirror
   Removal and installation of an internal mirror
   Removal and installation of the central console
   Removal and electric motor installation сдвижной panels of the hatch of a roof
   Removal and installation of a forward seat
   The device of a tension of a seat belt
   Security measures at the reference with the device of a tension of a belt
   Protection of the device of a tension of a belt
   Removal and installation of a back seat
   Removal and shelf installation under a headdress
   Removal and installation of jalousie of back glass
+ Onboard electric equipment
+ Electric equipment schemes
+ System of onboard diagnostics



Removal and installation of the central console

 REMOVAL

1. Uncover the gear change lever.

2. Remove the switch of the alarm system and the uniform lock. For this purpose through an aperture under the gear change lever wring out aside пенопластовую isolation and squeeze out the switch from below. Расстыкуйте штекерное connection.
3. Расстыкуйте штекерное connection прикуривателя through an aperture under the gear change lever.
4. Remove the block of management of a heater or the conditioner, address to Section Removal and installation of the block of management by a heater or the conditioner.

The management block has dense landing. Therefore at first remove the central console, and then squeeze out the block of management from an underside.

5. Squeeze out the switch under the management block through an aperture under the management block. Расстыкуйте штекерное connection.

6. Remove at the left and on the right lateral rugs. For this purpose turn out a bolt (1). Displace forward a lateral rug and disconnect it from clips.

7. Unscrew screws (2) and (3).

8. Uncover a lay brake from above consoles, incline it forward and disconnect from below.

9. Ослабьте the screw (4).
10. Turn out bolts (5) and (6), uncover.

11. Disconnect a lateral cover of the lever of a lay brake. For this purpose take a cover behind sideways aside seats of the driver and take out.

12. Press a back lattice of cooling (1) a little upward and a screw-driver sideways remove the holder банок or a box (2) (an arrow on an accompanying illustration).

13. Displace a cooling lattice downwards and remove it.

14. Turn out two screws of fastening (7) and (8).

15. Shift a seat completely back and turn out in a back part at the left and on the right below on two bolts of fastening, having removed a small screw-driver of a cover (11).

16. Wring out aside isolation of a casing of a gear change and turn out the screw (9).

17. Turn out a bolt (10).

18. Raise behind the central console a little. Расстыкуйте under it штекерное connection of a lamp of illumination of an ashtray. Preliminary mark the tip with a tape.
19. Establish both lobbies of a seat, a back and translate the lever of a gear change or the selector probably further back.

20. Raise behind the central console, pull back, towards a seat of the forward passenger and take out.


 INSTALLATION

1. Establish the central console from outside seats of the forward passenger.
2. Join штекерное connection of the switch of a lay brake under the console.
3. Establish the block of management of a heater or the conditioner, address to Section Removal and installation of the block of management by a heater or the conditioner.
4. Fix a cover of the lever of a gear change.