BMW 5 series E39

Since 1996-2001 of release

Repair and car operation



BMW E39
+ Introduction
+ The maintenance instruction
+ Current leaving and service
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of a body
   Care of the panels of furnish made of vinyl
   Care of an upholstery and salon rugs
   Repair of insignificant damages кузовных panels
   Repair of considerable damages of a body
   Kuzovnye backlashes
   Removal and installation of a forward bumper
   Removal and installation of shock-absorbers of a forward bumper
   Removal and installation of a back bumper
   Removal and installation of the shock-absorber of a back bumper
   Removal and installation of a forward wing
   Removal and cowl installation
   Adjustment of position of a cowl
   Removal and installation of a cover of a luggage carrier
   Adjustment of position of a cover of a luggage carrier
   Removal and installation of back facing of a luggage carrier
   Removal and installation of the lock of a cover of a luggage carrier/cylinder of the lock
   Removal and installation газонаполненного an emphasis of a cowl/cover of a luggage carrier
   Overlay replacement / a firm inscription
   Removal, installation and door adjustment
   Removal and installation of facing of a door
   Removal and door-lock installation
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock
   Removal and installation of the electric motor/microswitch of the uniform lock
   Removal, installation and adjustment of door glass
   Removal and installation electric стеклоподъемника
   Removal and installation of an external mirror
   Removal and installation of glass of a mirror
   Removal and installation of the case of an external mirror
   Removal and installation of an internal mirror
   Removal and installation of the central console
   Removal and electric motor installation сдвижной panels of the hatch of a roof
   Removal and installation of a forward seat
   The device of a tension of a seat belt
   Security measures at the reference with the device of a tension of a belt
   Protection of the device of a tension of a belt
   Removal and installation of a back seat
   Removal and shelf installation under a headdress
   Removal and installation of jalousie of back glass
+ Onboard electric equipment
+ Electric equipment schemes
+ System of onboard diagnostics


Removal and installation of a forward bumper

1 — facing
2 — a lattice opening
3 — a lattice closing
4 — a peak
5 — a lining
6 — a peak
7 — a lining

8 — a lattice
9 — a sealant
10 — a cover
11 — a peak
12 — a persistent lath
13 — a beam
14 — the buffer
15 — a bolt

The forward bumper is calculated in such a manner that it without damages bears blow at speed of the car to 4 km/hour. Thus energy of blow is absorbed by an internal aluminium beam and two hydraulic shock-absorbers. Shock-absorbers fasten to two easily removable deformed elements, so-called shock боксам. At speed to 15 km/hour energy is absorbed by deformation of hydraulic shock-absorbers and shock боксов that excludes damage of beams of the engine.

 REMOVAL

1. Turn away three external bolts of fastening of peaks of wheels at the left and on the right. Take out peaks sideways from a bumper (1). Address to an accompanying illustration.

It is not necessary to remove forward wheels.

2. Disconnect from above and remove a decorative lattice.

3. Turn away bolts of fastening Torx T50 of a bumper to shock-absorbers at the left and on the right and remove a bumper.

4. Расстыкуйте штекерное connection of antifog headlights and-or disconnect hoses фароочистителей. Press hoses clips that the liquid did not follow.

 

 INSTALLATION

1. If it is necessary, complete bumper knot.
2. Establish horizontally a bumper by means of the assistant. Join штекерное connection of antifog headlights and-or connect hoses фароочистителей.
3. Insert a bumper in lateral directing and press it.
4. Expose a bumper in parallel a body and fix screws the moment of 40 Nanometers.

 

5. The distance between a bumper and a body should make And = 5 1 mm.

6. Adjust height of a bumper turn of plastic inserts (5) in shock-absorbers.

7. Put a decorative lattice, insert rivets and press them заподлицо.
8. Fix a forward peak of a wheel.