BMW 5 series E39

Since 1996-2001 of release

Repair and car operation



BMW E39
+ Introduction
+ The maintenance instruction
+ Current leaving and service
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of a body
   Care of the panels of furnish made of vinyl
   Care of an upholstery and salon rugs
   Repair of insignificant damages кузовных panels
   Repair of considerable damages of a body
   Kuzovnye backlashes
   Removal and installation of a forward bumper
   Removal and installation of shock-absorbers of a forward bumper
   Removal and installation of a back bumper
   Removal and installation of the shock-absorber of a back bumper
   Removal and installation of a forward wing
   Removal and cowl installation
   Adjustment of position of a cowl
   Removal and installation of a cover of a luggage carrier
   Adjustment of position of a cover of a luggage carrier
   Removal and installation of back facing of a luggage carrier
   Removal and installation of the lock of a cover of a luggage carrier/cylinder of the lock
   Removal and installation газонаполненного an emphasis of a cowl/cover of a luggage carrier
   Overlay replacement / a firm inscription
   Removal, installation and door adjustment
   Removal and installation of facing of a door
   Removal and door-lock installation
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock
   Removal and installation of the electric motor/microswitch of the uniform lock
   Removal, installation and adjustment of door glass
   Removal and installation electric стеклоподъемника
   Removal and installation of an external mirror
   Removal and installation of glass of a mirror
   Removal and installation of the case of an external mirror
   Removal and installation of an internal mirror
   Removal and installation of the central console
   Removal and electric motor installation сдвижной panels of the hatch of a roof
   Removal and installation of a forward seat
   The device of a tension of a seat belt
   Security measures at the reference with the device of a tension of a belt
   Protection of the device of a tension of a belt
   Removal and installation of a back seat
   Removal and shelf installation under a headdress
   Removal and installation of jalousie of back glass
+ Onboard electric equipment
+ Electric equipment schemes
+ System of onboard diagnostics



Removal and installation of a back bumper

1 — facing
2 — a back persistent lath
3 — the central peak
4 — a lateral persistent lath
5 — a peak
6 — a thermal protection
7 — a rivet
8 — the holder
9 — a cover of a towing hook
10 — a cover

11 — a clip
12 — the amplifier
13 — саморез
14 — a nut
15 — a sliding element
16 — a towing hook
17 — a beam
18 — a bolt
19 — consolidation
20 — the shock-absorber

The back bumper is calculated in such a manner that it without damages bears blow at speed of the car to 4 km/hour. Thus energy of blow is absorbed internal стеклопластиковой by a beam and two hydraulic shock-absorbers.

 REMOVAL

1. Turn away bolts of fastening of the left and right back peaks of wheels. For this purpose take out a clip, preliminary having beaten out pins in the centre of clips by means of a cranked face key (2.5 - 3.0 mm). If pins have a cover, take out at first pins a screw-driver, then remove a clip. After that remove peaks of wheels sideways at shock-absorbers.

It is not necessary to remove wheels.

2. Open a luggage carrier, remove back facing, address to Section Removal and installation of back facing of a luggage carrier.

3. Turn away three nuts of fastening of a bumper a key of 13 mm at the left and on the right.

4. At the car with the remote control of a parking cut off a tape collar, расстыкуйте штекерное connection and release a cable. Delay a bumper a little back and take out the cable plug and a cable.
5 Take out a bumper back by means of the assistant.


 INSTALLATION

1. If it is necessary, collect a bumper in one knot, see иллюстр. In the section beginning.

2. If it is necessary, put on the shock-absorber a plastic cap. The cap at shock-absorber removal often remains in a nest.

3. Insert a bumper by means of the assistant in lateral directing (1) and displace it back, establish sideways a forward element and shift it against the stop forward. Thus a lobby the directing should come into a hook (2) at a bumper.

4. At the car with the remote control of a parking insert the cable plug and a cable. Join штекерное connection and fix a cable a tape collar, also as before removal.
5. Raise a bumper a little, will expose it in parallel and fix the moment of 20 Nanometers. The distance between a bumper and a body should make 5±1 mm.
6. The height of installation of a bumper is regulated at the removed shock-absorber by turn of a plastic insert with internal шестигранником.
7. Establish back facing in a luggage carrier.
8. Establish back peaks of wheels, fix clips and insert against the stop safety pins.