BMW 5 series E39

Since 1996-2001 of release

Repair and car operation



BMW E39
+ Introduction
+ The maintenance instruction
+ Current leaving and service
+ The engine
- Systems of cooling, heating
   - Cooling system
      Check of system of cooling
      Removal, installation and thermostat check
      Removal and installation of the fan and муфты the fan
      Removal and installation of a broad tank
      Removal and radiator installation
      Removal and installation of the pump of a cooling liquid
   + Heater
   + Air conditioner
+ The power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Electric equipment schemes
+ System of onboard diagnostics


Removal and radiator installation

In the course of long operation of the car channels in a radiator can be narrowed as a result of adjournment to exhaust, containing in a cooling liquid. Thereof efficiency of process of cooling and the engine sharply decreases overheats. In this case it is necessary to change a radiator.
If oil has got to a radiator, for example, owing to defect of a sealing lining of a head of cylinders, it is necessary to remove and wash out a radiator and a broad tank after repair by a cleaner. For this purpose it is required about 2 l of a cleaner. After radiator installation it is necessary to fill some times all system of cooling with hot water and to merge it. Water after system washing should be utilised in appropriate way.

1 — a radiator
2 — a broad tank
3 — a sealing ring
4 — a sealing ring
5 — a cover
6 — a bolt
7 — a stopper

8 — the union of removal of air
9 — a stopper
10 — the thermorelay, only for the conditioner
11 — a stopper
12 — a sealing ring
13 — the level gauge
14 — a sealing ring


 REMOVAL

1. Remove the fan, address to Section Removal and installation of the fan and муфты the fan.
2. Merge cooling liquid and utilise it, address to Section Replacement of a liquid of system of cooling. Check of frost resistance of a cooler. Visual check of system of cooling.

3. Remove hoses of a cooling liquid of the big diameter from above and from below a radiator, preliminary having opened collars. Address to an accompanying illustration.

4. Disconnect a cable from the gauge of level (13) at the left below at a radiator. Address to an illustration before the table.
5. In the presence of the conditioner расстыкуйте штекерное connection of the thermorelay (10) on the right at a radiator.

6. Remove hoses of an oil radiator (if it is available) АТ for a radiator. Collect the flowed out oil and utilise it. Hoses close, that the dirt has not got to them. Address to an accompanying illustration.

Radiators of the hydraulic booster of a wheel, the conditioner and, as a rule, АТ are before an engine radiator in the holder. For removal of these radiators it is necessary to remove an engine radiator preliminary. It is necessary to open a contour of cooling of the conditioner only on HUNDRED with application of special means. There is a danger of accident.

7. Remove a sealing uvula (1) upward. Turn away bolts (2) at the left and on the right. Remove both holders of a radiator (3). Address to an accompanying illustration.

8. Take out a radiator upward.

Radiator plates have sharp edges. Therefore for radiator removal it is recommended to use mittens.


 INSTALLATION

1. Check up all hoses of a cooling liquid on presence of cuts, cracks and other damages. If it is necessary, replace them. Check up both rubber support of a radiator.

2. A radiator insert from above so that rubber support have risen precisely into place. Address to an accompanying illustration.

3. Press a radiator and fix holders. Press on a sealing uvula.
4. Fix oil hoses АТ with new consolidations on a radiator. The moment of an inhaling of 20 Nanometers. Check up level of oil АТ, address to Section Check of level and replacement of oil of automatic transmission.
5. Put on hoses of a cooling liquid and fix their collars.
6. Connect a cable at the thermorelay and the level gauge if they were disconnected.
7. Establish the fan, address to Section Removal and installation of the fan and муфты the fan.
8. Fill system with a liquid and remove from it air, address to Section Replacement of a liquid of system of cooling. Check of frost resistance of a cooler. Visual check of system of cooling.
9. Start and warm up the engine and check up шланговые connections on tightness.
10. Check up level of a cooling liquid, if necessary add.