BMW 5 series E39

Since 1996-2001 of release

Repair and car operation



BMW E39
+ Introduction
- The maintenance instruction
   Controls, devices and control lamps
   Zapornye devices and the anticreeping alarm system
   The salon equipment
   Safety systems
   Fuel refuelling, start and engine stop
   Lay brake
   Manual box of a gear change (РКПП)
   Automatic transmission (АТ) *
   Темпостат
   The alarm system of emergency rapprochement at a parking (PDC) *
   System of automatic stabilisation of stability with a regulator of traction effort (ASC+T)
   Electronic adjustment of rigidity of amortisation (EDC) * and adjustment of a road gleam
   Illumination
   Heating and ventilation system
   Automatic кондиционер*
   Independent systems of heating and ventilation
   System самодиагностики*
   The travelling computer
   Обкатка
   The Katalitichesky converter
   Antiblocking system of brakes (ABS)
   Movement with the trailer
   Luggage carrier on a roof
   Automobile телефон*
   Radio reception
   Readjustment of headlights
   Cowl
   Automobile radio receiver
   Audiosystem of type Hi-Fi with DSP*
   Sign emergency остановки*
   Аптечка*
+ Current leaving and service
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Electric equipment schemes
+ System of onboard diagnostics


Enjoy the convenience of streaming your favorite content on Soap2day.

The salon equipment

Стеклоподъемники

Using стеклоподъемниками is possible after ignition key turn in position 1.
If to press the on-off switch without transition for a point of the raised resistance glass will move during all time of keeping of the switch in this position.
By short-term pressing the switch with transition for a point of the raised resistance it is realised стартстопный a mode at which glass movement occurs automatically.
For its stop it is necessary to press the switch in the same way once again.

On a door of the forward passenger and in a back part of a body (at a complete set of back doors electric стеклоподъемниками *) under glasses separate switches are established.

Leaving the car, always take with itself the ignition key that, for example, children could not put in action стеклоподъемники and put itself a trauma.

After deenergizing of ignition using possibility стеклоподъемниками remains, if:
- The key is in position 1 or 0
- It is taken out from the lock, and also at some export updatings before opening of forward doors
Or
- Within 15 minutes after their first opening

About automatic opening and closing of glasses by key turn in the lock of a door or by means of remote radio management address to Razdelu Zapornye devices and the anticreeping alarm system.

Travmozashchitnaja function electric стеклоподъемников

If at the moment of glass lifting to concern реечного contact at an aperture upper edge glass will stop and it will a little be lowered a little.

This function can be disconnected (for example, at attempt of the extraneous person to get in car outside), if to keep the switch стеклоподъемника in position стартстопного control mode.

The switch-safety lock

With its help you can prevent inclusion стеклоподъемников from a back seat, for example, children being there.

If on a back seat there are children always press a safety lock key. Uncontrollable closing of glasses can lead to traumas.

The hatch with podemno-sdvizhnoj крышкой*

Management of a hatch cover probably already after ignition key turn in position 1.

 •  Lifting: press the switch. The cover in a ceiling upholstery will move only on some centimetres back.
  •  Opening: shift the switch back to a resistance point.
  •  Closing: shift the switch forward to a resistance point.

Uncontrollable, without appropriate care closing podemno-sdvizhnoj hatch covers can lead to traumas. Leaving the car, always take out a key from the ignition lock that, for example, children could not involve a cover of the hatch and put itself a trauma.

In salon there will be no depression and draughts if at the open or lifted cover of the hatch pressure-blowing apertures are completely open and - in case of need - air giving will be increased.

After deenergizing of ignition possibility of using the hatch remains, if:
- The key is in position 1 or 0
- It is taken out from the lock,
And also at some export updatings:
- Before opening of forward doors or
- Within 15 minutes after their first opening

About automatic opening and closing of a cover of the hatch by key turn in the lock of a door or by means of remote radio management address to Razdela Zapornye materials of the device and the anticreeping alarm system.

Автоматическое* Opening and closing

The hatch cover opens and closed automatically if you shift the switch in a corresponding direction for a point of the raised resistance and then release it.

At an open cover the switch contact in a direction to "Lift" allows to shift a cover in final position of lifting.

At the raised cover the switch contact in a direction to "Open" allows to shift a cover in final open position.

The repeated contact of the switch allows to stop movement.

To raise the closed cover in this mode it is impossible.

Travmozashchitnaja function

If in the course of closing the hatch cover approximately in the middle of the course encounters an obstacle it will stop and hardly will be removed back.

This function can be disconnected (for example, at a heavy course of a cover on directing to frosty weather, or at attempt of the extraneous person to get into the car outside) if to translate the switch for a point of the raised resistance and to keep it in this position.

Обесточивание or malfunction

After обесточивания (for example, as a result of a detachment of the plug of the accumulator) it is possible to raise a cover only. In this case:

1. Lift a hatch cover against the stop.

2. Within approximately second keep the switch in the pressed position.

At malfunction in an electric equipment the hatch can be opened or closed manually. For this purpose:

1. Take out a plafond, give a hand in an aperture and squeeze out a cover.

2. Having removed заглушку (shown by an arrow) and taking from the complete set of the driver's tool a key for internal шестигранников, rotate it the mechanism of moving of a cover of the hatch in the necessary direction


Podemno-sdvizhnaja cover of the hatch with glass шторкой

Management of a cover and its work are carried out in the same way as it is described earlier. To open the raised cover, keep the switch in position to "Open" while the cover will not reach demanded position.

If the hatch cover rises, the cover in an upholstery of a ceiling moves back a little, and at opening it opens together with a hatch cover. It remains in open position and if necessary can be closed at any moment.

Sun-protection штора*

For inclusion of a drive of a curtain press a key. The drive works already after ignition key turn in position 1.

Sun-protection curtains back lateral стекол*

Each of curtains is extended for a loop and fixed in the fastening.

Seats

Seats as the major element of the chain connecting the person, a running gear and road, have been developed with special carefulness. The advanced methods, as, for example, САПР (systems of automatic designing), methods of final elements, and also control systems with electronic control were thus used.

Degree of amortisation of shock influences from outside roads has been carefully brought into accord with running gear characteristics. The stable bearing design of seats provides together with seat belts, натяжителями belts and, certainly, inflatable pillows of safety the highest level of safety. Thanks to multilayered structure наполнителя seats, to high percentage of natural fibres and difficult internal system of ventilation of a seat the person during movement - and even on long trips - feels расслабленно and does not get tired. Lumbar and humeral support provide optimum position of a backbone.

Adjustment of seats

For the sake of your personal security we address to you with the request to observe following rules of adjustment of seats.

Do not regulate a seat of the driver on the move. Its unexpected displacement can cause control loss over the car and lead to failure. The seat belt should as it is possible to adjoin to a body more densely. Otherwise at head-on collisions the zone belt can come off upwards on hips and injure the bottom part of a stomach. Besides at leaky adjoining belt its keeping effect is realised with delay.

It is inadmissible, that during movement of the car the back of a forward seat deviated far back (it concerns first of all a passenger seat) as thus in case of failure there is a danger “проскальзывания” the person under a seat belt which in that case cannot execute the protective function.

Forward seats cannot be shifted back if the car moves under a bias (for example, on a ramp of many-storeyed garages or on mountain roads) as it is thus possible отцепление systems of automatic adjustment of a belt on height.

Seats with manual adjustment

1. Longitudinal adjustment: Having pulled for the handle, shift a seat in position convenient for. Having released the handle, slightly shake a seat forward-back that it has reliably stopped.
2. Adjustment on height: Having pulled for the handle, adjust seat height, loading a pillow with a body weight or half-rising from it.
3. Back adjustment: Having pulled for the handle, adjust a back inclination, leaning back on it or moving forward.
4. Adjustment of an angle of slope of a pillow (only for a seat of the driver): Having pulled for the handle, displace a pillow before the necessary position.

For unloading позвоночных disks sit down with the maximum shift back, leaning all back against a seat back. Ideal the pose at which the head settles down on one straight line with a backbone is considered.

To reduce pressure of muscles at distant trips, it is possible to increase a back inclination some. Thus driving possibility when lying on the highest point of a wheel of a hand are slightly bent in elbows, however, should remain.

Lumbar опора*

The description of a firm seat of the raised comfortableness see more low.

Headrests

Headrests can be regulated on height, extending them from nests or pushing back.

The inclination of headrests can be regulated, turning them round a horizontal axis.

Headrests weaken traumatic consequences of failures for cervical vertebras.

The middle of headrests should settle down approximately at level of ears.

Seats sports типа*

This seat has an additional possibility of adjustment of a popliteal support.

Having pulled for the handle, establish a popliteal support in position convenient for you.

Seat with электрорегулировкой*

1 — adjustment of an inclination of a pillow

2 — longitudinal adjustment of a seat

3 — seat adjustment on height

4 — adjustment of an inclination of a back

5 — adjustment of height of a headrest

The headrest angle of slope is regulated manually.

For the sake of your personal security necessarily observe instructions on the adjustment, resulted above.

Firm seat comfortable типа*

For this seat adjustments of position of lumbar and humeral support are in addition provided.

1. A lumbar support

Pressing the switch in front or behind reaches accordingly increase or reduction of camber of a contour of a back.

By pressing the top or bottom part of the switch the convex zone of a contour is displaced upwards or downwards.

The back contour can change so that its acting part was entered in a hollow of lumbar department of a backbone, creating a support for it.

Thus, the support of the top department of a basin and a backbone, promoting correct and free landing is provided.

2. A humeral support

By pressing the on-off switch the angle of slope of the top part of a back changes.

Thanks to such adjustment опирание backs it is provided and in a humeral zone. It does landing more freely and unloads muscles of shoulders.

Installation of seats will be optimum at observance resulted below recommendations.

For the driver and the forward passenger:
1. Take away the top part of a back to a limit back.
2. Adjust a seat on optimum landing according to the description above.
3. Bring the top part of a back forward, having created a convenient support for shoulders.

For the forward passenger at the back rejected back:
1 Take away the top part of a back to a limit back.
2 Slightly increase a pillow inclination.
3 Slightly increase a back inclination.
4 Displace the top part of a back forward.

Changing longitudinal position of a seat, achieve that the seat belt densely adjoined, as before, to a body, differently it cannot execute the protective function.

Heating сидений*

For heating of a pillow and a seat back it is necessary to turn preliminary the ignition key in position 2. For inclusion and deenergizing it is necessary to press a key.
At the included heating of a seat the green control lamp which has been built in in a key burns.
Intensity of heating is established by a corrugated castor - regulation occurs in a thermostatic mode.
The minimum temperature
The maximum temperature

Adjustment of position of a steering wheel

Manual adjustment

1. Take away downwards the lock handle.

2. Having occupied a correct pose on a seat, adjust longitudinal position and a steering wheel angle of slope.

3. Return the lock handle in a starting position.

In order to avoid failure do not regulate a steering wheel on the move.

Электрорегулировка*

Steering wheel adjustment is possible in four directions corresponding to positions of the lever of the switch.
In order to avoid failure do not regulate a steering wheel on the move.

About work of the device remembering installation of a steering wheel, and also a seat and mirrors, address to materials more low in this Section.

Heating of the helmsman колеса*

For heating of a steering wheel it is necessary to turn preliminary the ignition key in position 2. For inclusion and deenergizing it is necessary to press the button shown by an arrow.
At the included heating of a steering wheel the control lamp which has been built in in the button burns.

If on the car the multipurpose steering wheel without the heating button on its place the button рециркуляционного a mode (address to Section Controls and devices) settles down is established.

Mirrors

External rear-view mirrors

1 — the switch for adjustment of position of a mirror in four directions

2 — the switch from one mirror on another

3 — a key for closing and раскрывания mirrors (only in a combination to the complete set of neosticking together mirrors *, see more low)

As a result of pressing a mirror key nestle on a body or get divorced in the parties that is convenient at journey through a sink, at movement on narrow streets, and also for return of mirrors to a starting position if they were earlier casually displaced forward.

To press mirrors to a body it is possible only at the motionless car or at speed no more than 10 km/h.

Position of mirrors can be regulated and manually, turning them for a fringing of glasses.

About work of the device remembering installation of mirrors, and also a steering wheel and a seat, address to materials more low in this Section.

External, асферически the bent part of a reflective surface provides at some distortion of the image больший review sector in comparison with an internal, convex part. The corner of the back review as a result increases and the so-called "dead" zone is reduced.

The distant mirror from the driver has more convex reflective surface in comparison with a mirror on a door of the driver. Visible subjects in it seem more remote, than actually. It is therefore only conditionally suitable for an estimation of distance to moving behind vehicles. Told concerns and to external асферически the bent part of a mirror.

Electroheating

The heating of both mirrors is carried out automatically depending on air temperature at ignition key turn in position 2.

Rear-view mirror in salon

For reduction of blinding action of headlights going behind cars it is necessary to turn small рычажок.

Cosmetic mirrors with подсветкой*

To take advantage of a mirror, cast away a sun-protection peak downwards and if the mirror is closed, shift its cover aside.

Illumination of mirrors joins already at ignition key installation in position 1.

Sun-protection peaks

It is possible not only to throw back peaks downwards, but also to take aside to lateral glasses.

Neosticking together mirror back вида* in salon

Reflective ability of a mirror automatically smoothly decreases depending on brightness of the general illumination and blinding action of headlights going behind cars.

At inclusion of transfer of a backing or while translating control lever АТ in position R the mirror is automatically switched to a mode of full reflexion without blackout.

For normal work of a mirror it is important to cover and keep nothing clean its photo cells. The light gauge directed forward measures intensity of light in the mirror case in front of the car. The second light gauge is in the mirror. The electronic system of adjustment compares values of intensity of light in front and behind. The difference of values is the defining size for change of electric pressure on a liquid crystal layer of a mirror. This layer reacts to change of pressure and provides smooth blackout of a mirror. Thus, necessity most disappears to regulate degree of blackout of a mirror that allows the driver to concentrate the attention to road completely.

The complete set neosticking together зеркал*

Both external rear-view mirrors are executed also with possibility of automatic smooth reduction of reflective effect. Besides, using a key 3 (illustration), they can be put and again to open in the parties.

The device remembering positions of a seat, mirrors and the helmsman колеса*

Storing and reproduction to three variants of installation of a seat, mirrors and a steering wheel (if its electroadjustment only is provided) is possible.

Use of system of storing of position of a lumbar support is not provided.

Storing

1. Having inserted a key into the ignition lock, turn it in position 1 or 2.
2. Adjust a seat, mirrors and a steering wheel, having established them in position convenient for.
3. Press key MEMORY (Memory). The control lamp built in in it Thus will light up.
4. Press at own discretion a key 1, 2 or 3. Thus the control lamp will go out.

Restoration

The ignition key is in position 1:
Press, without keeping, the necessary key (1, 2 or 3).
At influence on any switch of electroadjustment of a seat or by pressing one of keys of memory installation process will immediately interrupt.

The door of the driver is closed, and a key in the ignition lock will turn in position 0 or 2 or in general will take out from it:
(1, 2 or 3) it is necessary to keep the necessary key pressed to full end of process of installation.
Unintentionally having pressed key MEMORY, press it once again that the control lamp has gone out.

Automatic correction of position of a mirror at movement by a backing

1. Translate the switch of management of mirrors (it is shown by an arrow) in position “Fahrerspiegel” (the Mirror on the party of the driver).

2. At inclusion of transfer of a backing or at installation of control lever АТ in position R the distant mirror slightly will deviate the driver so that, for example, at arrival on parking it was possible to see the bottom part of a board of the car and edge бордюрного a stone.

You can and disconnect this function, having translated the switch of management of mirrors in position “Beifahrerspiegel” (the Mirror on the party of the passenger).

Ware box

 • Opening:
Pull for the handle. Box illumination thus will join.

 • Closing:
Slam a cover movement upwards.

 • Lock-out:
For box lock-out it is necessary to take advantage of a key from the uniform lock. After that to unlock it it will be possible also only a key from the uniform lock.

In order to avoid traumas at failures it is recommended not to leave a ware box without need opened.

Accumulator room portable лампа*

The lamp is at the left in a ware box.

Thanks to presence of the device protecting its accumulator from a recharge, it can be stored constantly included in the socket.

To insert a lamp a plug into the socket it is possible only in the switched off condition, differently there is a danger of an overload and lamp damage.

Compartments for storage of small things

The box cover in front on the oblique party of the average console is executed сдвижной.

At a complete set of the car the holder кассет* each branch for cartridges opens pressing of the small button.

The open compartment is to the left of a steering column.

If the car is completed with a compartment with a folding cover * to open it, it is necessary to pull for the handle downwards and to close - it is necessary to slam a cover movement upwards.

Compartment on the average console between two forward seats. To open a compartment, it is necessary to undertake dredging in front and to pull a cover upwards. In this compartment phone if you wish to equip with it the car is established.

Or niches for small things you will find pockets also on any of doors and from the back party of backs of lobbies сидений*.

The holder for банок with напитками*

On two holders for банок with drinks are in a compartment from a face sheet of the average console, and also behind, in the end of the average console under lattices.

They open simple pressing and to close them, it is necessary to push holders back.

Ashtray спереди*

Opening:

The ashtray opens simple pressing in a direction shown by an arrow.

Extinguish a cigarette in a reception nest of an ashtray without superfluous effort, preliminary having shaken ashes.

Clearing:

Press cover edge (as shown an arrow). The ashtray will move upwards then she can be taken from a nest.

Прикуриватель*

Press deepening (it is shown by an arrow) and drown прикуриватель in a nest.

As soon as it will be pushed out back, it can be taken out.

Hot прикуриватель hold only for the handle, differently there is a danger of reception of burns.

Прикуриватель remains in an efficient condition and after extraction of a key from the ignition lock. Therefore never leave in the car of children without supervision.

Nest прикуривателя

This nest can use as a plug receptacle for connection of a portable lamp, a vacuum cleaner and other consumers of a current capacity approximately to 200 Vt and with working pressure 12В. On the car in a complete set for non-smoking прикуриватель it is closed demountable заглушкой. In order to avoid nest damage прикуривателя do not try to insert into it an improper plug.

Ashtrays сзади*

Opening:

The ashtray opens pressing dredging.

Clearing:

Press cover edge (as shown an arrow).
The ashtray will move upwards then it can be taken out.

The device for transportation lengthy предметов*

The back of a back seat is divided in a proportion 1/3:2/3. For packing of lengthy subjects you can cast away each of these parts of a back.

To cast away a back part, undertake deepening and pull a back forward (an arrow 1).

At return installation watch that the back was reliably fixed on a place. Thus the red toddler should leave downwards (an arrow 2).

You can block each part of a back, using a key from the uniform lock.

Thereby access to a luggage carrier from salon that is convenient when you transfer a key 3 from a door and the ignition lock (address to Razdelu Zapornye devices and the anticreeping alarm system) to the employee of parking place in hotel is prevented.

Cover for transportation лыж*

In a cover it is possible to transport, without being afraid for their safety and cleanliness of salon, to four pairs skis.

Taking into account length of a cover and additional space a luggage carrier it is possible to load skis in length in the car to 2.10 m. At loading of skis in length of 2.10 m capacity of a cover it is reduced, so into it can enter no more than two pairs skis of the specified maximum length.

Removal of a back dividing armrest
(It is not provided at use on the car of the device for transportation of lengthy subjects. Address to materials more low).

1. Cast away the central dividing armrest.

2. Remove the facing panel fixed on “липучках”, and put it on an armrest.

3. Undertake one hand a forward part of an armrest, and other hand for its back part and sharply lift it upwards (as shown an arrow).

Armrest installation

Insert an armrest from above and press it downwards so that it was audible, as it will be latched in holders.

Watch that lateral pins have not damaged a seat upholstery.

Loading

1. Press the button shown by an arrow 1. There will be an unlocking of a folding cover of the hatch in a luggage carrier.

2. Having reduced the clamps shown by arrows 2, cast away a cover.

3. Straighten a cover and lay it between forward seats. The fastener of type "lightning" is intended for access simplification to the things loaded into a cover, and also for its accelerated drying.

4. A folding cover of the loading hatch from outside a luggage carrier fix on the magnetic holders who are available from the bottom party regiments behind a back seat.

The request to watch that skis were loaded into a cover only pure, and to avoid damages of a cover by keen edges.

Skis or the other lengthy subjects loaded into a cover, should fasten the belt sewn to a cover tightened by means of a buckle intended for it.

To clean a cover, it is necessary to operate in return sequence.

Cover for transportation of skis in a combination to the device for transportation of lengthy subjects

1. Cast away a back dividing armrest, remove the facing panel fixed on “липучках” and put it on an armrest.

2. Press downwards the button 1 and cast away a cover forward.

3. Press the button 2. The cover in a luggage carrier will be unblocked.