BMW 5 series E39

Since 1996-2001 of release

Repair and car operation



BMW E39
+ Introduction
+ The maintenance instruction
+ Current leaving and service
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of a body
   Care of the panels of furnish made of vinyl
   Care of an upholstery and salon rugs
   Repair of insignificant damages кузовных panels
   Repair of considerable damages of a body
   Kuzovnye backlashes
   Removal and installation of a forward bumper
   Removal and installation of shock-absorbers of a forward bumper
   Removal and installation of a back bumper
   Removal and installation of the shock-absorber of a back bumper
   Removal and installation of a forward wing
   Removal and cowl installation
   Adjustment of position of a cowl
   Removal and installation of a cover of a luggage carrier
   Adjustment of position of a cover of a luggage carrier
   Removal and installation of back facing of a luggage carrier
   Removal and installation of the lock of a cover of a luggage carrier/cylinder of the lock
   Removal and installation газонаполненного an emphasis of a cowl/cover of a luggage carrier
   Overlay replacement / a firm inscription
   Removal, installation and door adjustment
   Removal and installation of facing of a door
   Removal and door-lock installation
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock
   Removal and installation of the electric motor/microswitch of the uniform lock
   Removal, installation and adjustment of door glass
   Removal and installation electric стеклоподъемника
   Removal and installation of an external mirror
   Removal and installation of glass of a mirror
   Removal and installation of the case of an external mirror
   Removal and installation of an internal mirror
   Removal and installation of the central console
   Removal and electric motor installation сдвижной panels of the hatch of a roof
   Removal and installation of a forward seat
   The device of a tension of a seat belt
   Security measures at the reference with the device of a tension of a belt
   Protection of the device of a tension of a belt
   Removal and installation of a back seat
   Removal and shelf installation under a headdress
   Removal and installation of jalousie of back glass
+ Onboard electric equipment
+ Electric equipment schemes
+ System of onboard diagnostics



Removal, installation and door adjustment

Installation and removal of forward and back doors are carried out equally.

 REMOVAL

1. Turn out a bolt (1) from each loop by means of a head of 10 mm. Address to an accompanying illustration.
2. Wring out sideways a screw-driver a stopper (2) from an axis (3).
3. Beat out upward оправкой an axis (3) door brakes.

4. Remove a door from loops and put it on a support. The support height should be such to exclude a tension of electric wires.

Do not damage a paint and varnish covering of a door and a forward wall. For protection of their surfaces it is possible to stick with a tape.

5. Disconnect the holder of the tip (an arrow on an accompanying illustration). Расстыкуйте штекерное connection.

6. Lift колодку. Thus, штекерное connection undocks.


 INSTALLATION

1. Join штекерное connection and fix it. Insert connection into a door rack. Fix the holder.

2. Put a door on the top and bottom loops. The assistant for this purpose is required. The door an axis (3) goes. By means of washers (5) it is possible to adjust door position on height. At installation of an old door adjustment, as a rule, is not required.
3. Screw in each loop a bolt (1).
1 — a bolt
2 — a body loop top
3 — a loop axis
4 — a door loop top
5 — a washer
6 — a lock washer

4. By means of a hammer insert an axis of a door brake and застопорьте it.
5. Close a door and check up uniformity of a backlash between a door and a body. If a backlash non-uniform, ослабьте bolts of fastening of loops also adjust door height the top bolts.

At installation of a new door under a loop the remote washers are established, allowing to displace a door outside and inside.

The door should be levelled to (drive) only complete with hinged details, such as стеклоподъемник, has flown down etc. as the characteristic of displacement of a door depends on weight. At adjustment remove door consolidations. If forward and back doors have been removed, at first level a back door, then a lobby.

6. Ослабьте a bolt-1 запорного a finger on a rack In by means of key TORX, and ослабьте a bolt-2 so that запорный the wedge could be shifted. Do not change position запорного a wedge-3 on depth.

7. Raise and keep the door handle. Close a door, the height and an inclination запорного a wedge thereby is regulated.

To a direction запорного a wedge in a workshop it is applied щуп.

8. Cautiously open a door and tighten bolts with effort of 30 Nanometers.

Displacement of a forward edge of a door inside and a back edge outside no more than 1 mm is supposed. Worn out запорный the element should be replaced.