BMW 5 series E39

Since 1996-2001 of release

Repair and car operation



BMW E39
+ Introduction
+ The maintenance instruction
+ Current leaving and service
+ The engine
+ Systems of cooling, heating
+ The power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   Care of a body
   Care of the panels of furnish made of vinyl
   Care of an upholstery and salon rugs
   Repair of insignificant damages кузовных panels
   Repair of considerable damages of a body
   Kuzovnye backlashes
   Removal and installation of a forward bumper
   Removal and installation of shock-absorbers of a forward bumper
   Removal and installation of a back bumper
   Removal and installation of the shock-absorber of a back bumper
   Removal and installation of a forward wing
   Removal and cowl installation
   Adjustment of position of a cowl
   Removal and installation of a cover of a luggage carrier
   Adjustment of position of a cover of a luggage carrier
   Removal and installation of back facing of a luggage carrier
   Removal and installation of the lock of a cover of a luggage carrier/cylinder of the lock
   Removal and installation газонаполненного an emphasis of a cowl/cover of a luggage carrier
   Overlay replacement / a firm inscription
   Removal, installation and door adjustment
   Removal and installation of facing of a door
   Removal and door-lock installation
   Removal and installation of the external handle of a door
   Removal and installation of the cylinder of the lock
   Removal and installation of the electric motor/microswitch of the uniform lock
   Removal, installation and adjustment of door glass
   Removal and installation electric стеклоподъемника
   Removal and installation of an external mirror
   Removal and installation of glass of a mirror
   Removal and installation of the case of an external mirror
   Removal and installation of an internal mirror
   Removal and installation of the central console
   Removal and electric motor installation сдвижной panels of the hatch of a roof
   Removal and installation of a forward seat
   The device of a tension of a seat belt
   Security measures at the reference with the device of a tension of a belt
   Protection of the device of a tension of a belt
   Removal and installation of a back seat
   Removal and shelf installation under a headdress
   Removal and installation of jalousie of back glass
+ Onboard electric equipment
+ Electric equipment schemes
+ System of onboard diagnostics



Removal, installation and adjustment of door glass

 REMOVAL

1. Remove upward an external lath of window mine. Thus begin from below.
2. Remove door facing.

At the car with a lateral pillow of safety disconnect a cable of weight from the storage battery and remove a pillow, address to Section “Removal and installation of the lock of a door”. Observe security measures at work with a safety pillow, address to Security measure Section at work with a safety pillow.

3. Cautiously remove пенопластовую facing in a back part of cut of a door, incline it forward so that the bottom adjusting screws were free and fix in this position by a sticky tape.

4. Ослабьте bolts of fastening tightening колодки (arrows on an accompanying illustration).

5. Incline glass a little forward and take out back upward.


 INSTALLATION

1. Insert glass in tightening колодки.
2. Attach the switch стеклоподъемника. If it is necessary, attach a weight cable to a battery accumulator room.
3. Close glass so that there was a backlash of 10 mm.

4. Adjust glass position, having reached next sizes: And = 5.4 mm; In = 10 mm. Address to an accompanying illustration. For this purpose displace glass at opened колодках in a longitudinal direction or displace back колодку so that glass was in parallel a framework. In this position tighten screws the moment of 10 Nanometers.

5. Расстыкуйте штекерное switch connection стеклоподъемника. If it is necessary, disconnect a cable of weight from the storage battery.
6. Establish door facing. If it is necessary, establish a lateral pillow of safety, address to Section Removal and installation of facing of a door.
7. Establish an external lath of door mine so that it behind was заподлицо with a door edge.